Auxiliary Modules
TFWF 96 Test Fixture Wire Finder
The TFWF 96 Test Fixture Wire Finder is used for the individual wiring of a test fixture, when e.g. you have to duplicate a fixture or want to More ...
AdapLMXModul
Fixture power matrix 8 channels, controlled by I2C-Bus or RS232, channels 1-4 normally open contacts AC 4 A, 250 V, max. AC 1000 VA, DC 3 A, 30 More ...
RelMOD Module for Switching
max. 200 V and 0.5 A bei max. 10 W controlled via TTL-signal, no cabling, for mounting into the fixture More ...
HVRelMOD Module
with 2 normally open contacts for switching voltages up to 230 Veff at 5 A, controlled via TTL-signal, no cabling, for mounting into the fixture More ...
DACMOD Module
for creating voltages between 0 and 10 V or current between 0 and 25 mA, resolution 12 Bit, control via I2C-Bus, no cabling, for mounting into More ...
GenMOD Module
for creating output frequencies between 1 Hz and 65 kHz, resolution 1 Hz, output voltage in the sine range is 5 Vpp, squarewave output is a More ...
HFGenMOD TTL-Generator
programmable frequency 5 kHz to 30 MHz in three ranges can be set via coarse and fine potentiometer, pulse ratio 50/50, voltage supply 4.5 to More ...
PGenMOD Module
for generating pulse width from 0.5 µs up to several hundred ms repetition frequency up to 1 µs, output signal: TTL-gate, programming via More ...
OPAMOD Impedance Transformer
input impedance up to 1 TOhm max. signal frequency 150 kHz, without cabling, for mounting into the fixture More ...
OPTOMOD Module
Optical input/output isolation module made up of two opto-couplers, signal amplitude 0 to 5 V, maximum useable frequency 5 MHz, without cabling, More ...
HFPKMOD Module
for measuring peak voltages up to 100 MHz, no cabling, for mounting into the fixture More ...
HFMOD HF-Module
for measuring frequencies up to 1.1 GHz division ratio 1:128, input voltage range 500 mV to 5 V, without cabling, for mounting into the fixture More ...
FARBMod
Microprocessor-controlled LED-test module for test and evaluation of colours (e.g. of keys) and LEDs incl. colour and light intensity, with More ...
16FARBMod
Microprocessor-controlled LED-test module for automatic test and evaluation of colours (e.g. of keys) and LEDs incl. colour and light intensity, More ...
MicMOD
MicMOD Microphone Module gain can be set in the 3 levels x1100, x110 (Default), x11, without cabling, for mounting into the fixture More ...
StromMOD
Current measuring module for measuring external currents without CMMR-problems (Common Mode Error), no cabling, for mounting into the fixture More ...
TrigMessMOD
for measuring a triggered voltage in the range 0-5 V trigger via TTL-input with programmable delay More ...
ADAEEP
Module with integrated EEPROM (can be plugged on) for automatically finding the test program that fits the resp. exchange plate (for More ...
DUT_LED Module
DUT_LED Module optically displays the operating status (Good green, fault red); for mounting on the fixture plate More ...
BEE-Module
recognises if a PCB is placed in or removed from a REINHARDT-test fixture retroreflective sensor, class 1M laser, 5 VDC-supply, max. 50 mA, More ...
TempMOD
TempMOD I2C-Temperature-humidity module temperature -40 °C to +60 °C, resolution 0.01 °C, tolerance 0.2 °, relative humidity More ...
AKK Pneumatic Cable Clamp
with 24VDC magnetic valve cable cross sectional area 0,14 mm2 to 4 mm2, compressed air 6 bar, dimensions without magnetic valve 14 mm wide, 27 More ...
AKK 2.5 Pneumatic Cable Clamp
AKK 2.5 Pneumatic cable clamp with 24VDC magnetic valve, cable cross sectional area 0.14 mm2 to 2.5 mm2, compressed air 6 bar, dimensions More ...
Electric Circle Marker
Electric circle marker for marking tested PCBs engraves the PCB with a 2 mm circle, 6-12 VDC, approx. 100 mA for control, incl. fixing angle for More ...
Pneumatic Actuator
Pneumatic actuator, 10 mm shift and 3/2 way valve, 24 V, incl. supply connector, 500 mm hose for compressed air, compressed air 6 bar, pressure More ...
Actuator M12
Electronic Actuator M12 for moving keys and switches 12. mm shift (programmable in 170 steps), compressive force 6 N, I2C-Bus controlled; More ...
ProgMOD 16
ProgMOD 16 Programmer connector module 3fold exchangeable module for up to 8 connections, in order to either connect an RMX-channel or two More ...
HVT16 High Voltage Divider
for expanding the measuring range max. 1,000 V, impedance 10 MOhm, division ratio 1:60, for plugging onto the universal exchange plate for More ...
